Kia Optima Manuals

Kia Sedona: STG Spindle Repair procedures - Smart Tailgate System - Body Electrical System - Kia Sedona YP Service ManualKia Sedona: STG Spindle Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Body Electrical System / Smart Tailgate System / STG Spindle Repair procedures

Removal
[LH]
1.
Disconnect the negative (-) battery terminal.
2.
Remove the tail gate trim [LH].
(Refer to Body - "Tail Gate Trim")
3.
Disconnect the STG spindle connector (A).

4.
Using a screwdriver, loosen the bracket (B) mounting bolts after lifting the socket clips (A) up slightly.
5.
Remove the STG spindle assembly (C).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

   
•
Work in a group of two or more when removing and installing the STG spindle.
•
Take care not to close the tail gate while the STG spindle is removed.
[RH]
1.
Disconnect the negative (-) battery terminal.
2.
Remove the luggage side trim [RH].
(Refer to Body - "Luggage Side Trim")
3.
Remove the tail gate trim [RH].
(Refer to Body - "Tail Gate Trim")
4.
Pull up the bottom of rear A/C duct (A).

5.
Remove the third row seat belt upper anchor (A) after loosening the bolt.
Tightening torque:
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

6.
Loosen the mounting bolt (A).

7.
Remove the rear A/C duct (A) after loosening the bolt.

8.
Disconnect the STG spindle connector (A).

9.
Using a screwdriver, loosen the bracket (B) mounting bolts after lifting the socket clips (A) up slightly.
10.
Remove the STG spindle assembly (C).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

   
•
Work in a group of two or more when removing and installing the STG spindle.
•
Take care not to close the tail gate while the STG spindle is removed.
Installation
[LH]
1.
Install the STG spindle assembly.
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
2.
Connect the STG spindle connector.
3.
Install the tail gate pillar trim [LH].
4.
Connect the negative (-) battery terminal.
[RH]
1.
Install the STG spindle assembly.
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
2.
Connect the STG spindle connector.
3.
Install the rear A/C duct.
4.
Install the third row seat belt upper anchor.
Tightening torque:
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
5.
Install the luggage side trim [RH].
6.
Install the tail gate pillar trim [RH].
7.
Connect the negative (-) battery terminal.
Anti-Pinch Strip Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the tail gate trim. (Refer to Body - "Tail Gate Trim") 3. Disconnect the anti-pinch strip sensor connector (A). 4. R ...

Sun Roof
...

Other Information:

Variable Intake Solenoid (VIS) Valve Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the VIS valve connector. 3. Measure resistance between the VIS valve terminals 1 and 2. 4. Check that the resistance is within ...

Components and Components Location
Component Location 1. Battery2. AC inverter switch3. AC inverter unit4. AC inverter outlet ...

Categories

Copyright © www.kisedona.com 2016-2026