Kia Optima Manuals

Kia Sedona: SS-B Solenoid Valve(ON/OFF) Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sedona YP Service ManualKia Sedona: SS-B Solenoid Valve(ON/OFF) Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / SS-B Solenoid Valve(ON/OFF) Repair procedures

Inspection
1.
Turn ignition switch OFF.
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Disconnect the solenoid valve connector (A).

4.
Measure the resistance between power terminal (5) and signal terminal (12).
Specification : 10.0 ~ 11.0 Ω

Removal
1.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.
Tightening torque:
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
3.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
4.
Remove the wiring bracket (A) and the air breather hose (B).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

5.
Lift the vehicle after loosening valve body cover upper bolts.
6.
Remove the valve body cover (A) by loosening bolts.
Tightening torque:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

7.
Remove the solenoid valve harness (A) and oil temperature sensor (B) after removing the bolts.
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

8.
Remove solenoid valve support bracket (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

9.
Remove the SS-B solenoid valve (A).

Installation
1.
Install in the reverse order of removal.
   
•
The existing solenoid valve O-ring (A) must be replaced with new one. (Do not reuse it.)

•
The existing valve body cover gasket (A) must be replaced with new one. (Do not reuse it.)

•
Refill the automatic transaxle with fluid.
(Refer to Hydraulic System - "Fluid")
•
Confirm that there is no fluid leakage on connections after repairing.
SS-B Solenoid Valve(ON/OFF) Schematic Diagrams
Circuit Diagram ...

Inhibitor Switch Specifications
Specification ItemSpecificationPower supply (V)12Output typeCombination of output signals Signal Code Table 　PP-RRR-NNN-DDSignal "1"12V12V00000Signal "2"012V12V12V000Signal "3"00012V12V12 ...

Other Information:

Hitches
It's important to have the correct hitch equipment. Crosswinds, large trucks going by, and rough roads are a few reasons why you ...

Air conditioning
Kia Air Conditioning Systems are filled with refrigerant*. 1. Start the engine. Push the air conditioning button. 2. Set the mode to the position. 3. Set the air intake control to the outside air ...

Categories

Copyright © www.kisedona.com 2016-2026