Kia Sedona: Engine Oil Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Engine Mechanical System / Lubrication System / Engine Oil Repair procedures

Replacement

•	Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

•	Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.

•	In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.

1.	Park the car on level ground.

Drain engine oil.

(1)	Remove the oil filler cap (A).

(2)	After lifting the car, remove the oil drain plug (A) and drain oil into a container.

Replace the oil filter.

(1)	Remove the oil filter cap (A).

(2)	Replace the O-ring (B) of oil filter cap with a new one.

(3)	Replace the new oil filter element (C).

(4)	Check and clean the oil filter installation surface.

(5)	Apply clean engine oil to the new O-rings (B).

(6)

Lightly screw the oil filter cap (A) into place, and tighten it until the O-ring (B) contacts the seat.

Check the O-ring (A) so that it is installed correctly inside the cap.

(7)	Finally tighten it again to the specified tightening torque.

Fill new engine oil.

(1)

Install the oil drain plug (A) with a new gasket.

Tightening torque :

34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)

(2)

Fill with new engine oil while checking the oil level on the dipstick.

Capacity

Total : 6.5 L (6.87 US qt, 5.72 lmp qt, 1.72 US.gal)

Oil pan : 6.0 L (6.34 US qt, 5.28 lmp qt, 1.58 US.gal)

Drain and refill including oil filter :

5.7 L (6.02 US qt, 5.01 lmp qt, 1.50 US.gal)

•	Fill the crankcase to about half the capacity and then fill the remainder after waiting.

•	Do not fill oil over the ''F'' line and check frequently the level with the oil level gauge to ensure no overfilling.

(3)	Install the oil filler cap and the oil dipstick.

5.	Start the engine and check that no oil is leaking from the drain plug or oil filter.

Recheck the engine oil level.

When rechecking the engine oil level, be sure to warm up the engine enough. If the engine is not warmed up sufficiently, the measurement of the engine oil level may be less than the specification.

Inspection

Engine Oil Level

Be sure that the vehicle is on level ground.

1.	Warm up and stop the engine, and then wait for 5 minutes.

2.	Turn the engine off and wait for a few minutes (about 5 minutes) for the oil to return to the oil pan.

3.	Pull the dipstick out, wipe and re-insert it fully.

4.	Check that the oil level is between the "L" and "F" level marks on the engine oil level gauge.

If the level is low, check for leakage and add oil up to the full level mark.

Use a funnel to help prevent spilling the oil on engine components.

Do not fill the engine with oil to above the full level mark.

Engine Oil Appearance

1.	Check engine oil for white turbidity or heavy contamination.

2.	If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant. Repair or replace damaged parts.

Selection Of Engine Oil

Recommendation

–	ACEA A5 or above / 5W-30

Allowed Oil Grade

–	ACEA A3 or above

Allowed SAE Viscosity

For best performance and maximum protection of all types of operation, select only those lubricants which:

1)	Satisfy the requirement of the ACEA classification.

2)	Have proper SAE grade number for expected ambient temperature range.

3)	Have both an SAE grade number and ACEA service classification on the container; otherwise, it should not be used.

Flow Diagram

Engine oil flow diagram ...

Oil Filter Body Components and Components Location

Components 1. Oil filter body2. Gasket ...

Other Information:

Center Fascia Panel Repair procedures
Replacement [Center fascia upper panel] Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wra ...

Overdrive Clutch Control Solenoid Valve(OD/C_VFS) Description and Operation
Description • Overdrive clutch control solenoid valve is a Variable Force Solenoid (VFS) type. • When TCM supplies variable current to solenoid valve, hydraulic pressure of und ...

Kia Sedona: Engine Oil Repair procedures

Flow Diagram

Oil Filter Body Components and Components Location

Other Information:

Categories