Kia Optima Manuals

Kia Sedona: Front Washer Motor Repair procedures - Windshield Wiper/Washer - Body Electrical System - Kia Sedona YP Service ManualKia Sedona: Front Washer Motor Repair procedures

Third generation YP (2014-2025) / Kia Sedona YP Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Washer Motor Repair procedures

Inspection
Front Washer Motor
1.
With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
   
Before filling the reservoir tank with water, check the filter for any foreign material or contamination. If necessary, clean the filter.
2.
Connect positive (+) battery cables to terminal 2 and negative (-) battery cables to terminal 1.
3.
Check that the motor operates normally, the washer motor runs and water sprays from the front nozzles.
4.
If there is an abnormality, replace the washer motor.
[Front washer]
No.
Description
1
Ground
2
Windshield washer (+)

Washer Fluid Level Sensor Switch
1.
Disconnect the negative (-) battery terminal.
2.
Drain the washer fluid to less than 600 cc.
3.
Check for continuity between terminals No. 1 and No. 2 in each float position.
There should be continuity when the float is down.
There should be no continuity when the float is up.
4.
If the continuity is not as specified, replace the washer fluid level switch.

5.
If the continuity is not as specified, replace the washer fluid level switch (A).

Removal
Front Washer Motor
1.
Disconnect the negative (-) battery terminal.
2.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
3.
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard")
4.
Drain the washer fluid to less than 650 cc.
5.
Disconnect the washer hose (A) and washer motor connector (B).

6.
Remove the front washer motor (A).

Washer Fluid Level Sensor Switch
1.
Disconnect the negative (-) battery terminal.
2.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
3.
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard")
4.
Drain the washer fluid to less than 650 cc.
5.
Disconnect the washer fluid level sensor switch connector (A).

6.
Remove the washer fluid level sensor switch (A).

Reservoir Tank
1.
Disconnect the negative (-) battery terminal.
2.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
3.
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard")
4.
Drain the washer fluid to less than 650 cc.
5.
Disconnect the washer hose (B) after disconnecting the reservoir tank mounting clip (A).

6.
Disconnect the washer hose (A), washer fluid level sensor switch connector (B), and washer motor connector (C).
7.
Disconnect the mounting clip (D).

8.
Remove the reservoir (A) after loosening the mounting bolts.

Installation
Front Washer Motor
1.
If Necessary, clean the washer motor filter.
   
Before installing the pump motor, check the filter for any foreign material or contamination. If necessary, clean the filter in the pump motor.
2.
Install the front washer motor.
3.
Install the front washer motor connector.
4.
Install the front wheel guard [RH].
5.
Install the engine room under cover.
6.
Connect the negative (-) battery terminal.
Washer Fluid Level Sensor Switch
1.
Install the washer fluid level sensor switch.
2.
Install the washer fluid level sensor connector.
3.
Install the front wheel guard [RH].
4.
Install the engine room under cover.
5.
Connect the negative (-) battery terminal.
Reservoir Tank
1.
If necessary, clean the washer motor filter.
   
Before installing the pump motor, check the filter for any foreign material or contamination. If necessary, clean the filter in the pump motor.
2.
Install the reservoir tank.
3.
Install the washer motor hose and connectors.
4.
Install the front wheel guard [RH].
5.
Install the engine room under cover.
6.
Connect the negative (-) battery terminal.
Front Wiper Motor Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm. 3 ...

Heating,Ventilation And Air Conditioning
...

Other Information:

Antenna Components and Components Location
Components ...

Repair procedures
Replacement     Be careful not to damage the fender and body.     When removing the clips, use a clip remover. 1. Remove the front bumper ...

Categories

Copyright В© www.kisedona.com 2016-2025