Kia Sedona: Sunroof Motor Repair procedures

Third generation YP (2014-2025) / Kia Sedona YP Service Manual / Body Electrical System / Sun Roof / Sunroof Motor Repair procedures

Inspection

1.	Disconnect the negative (-) battery terminal.

2.	Remove the roof trim assembly. (Refer to Body - "Roof Trim Assembly")

3.	Disconnect the sunroof motor (A) connector. [Front] [Rear]

4.	Ground the terminals as the table below, and check that the sunroof unit operates.

Perform these input tests at the connector. If any test indicates a problem, find and correct the cause, and then recheck the system. If all input tests prove to be OK, replace the sunroof motor as it must be faulty.

Terminal	Test condition	Test: Desired result
12	IG2 ON	Check for voltage to ground: There should be battery voltage.
3	Under all conditions	Check for continuity to ground: There should be continuity.
1	Under all conditions	Check for voltage to ground: There should be battery voltage.

Adjustment

Resetting The Sunroof

Whenever the vehicle battery is disconnected or discharged, or the emergency handle was used to operate the sunroof, the sunroof system must be reset in the following procedure:

1.	Turn the ignition key to the ON position and then close the sunroof completely.

2.	Release the sunroof control lever.

3.	Press and hold the CLOSE button for more than 10 seconds until the sunroof fully closed and then recovered slightly.

4.	Release the sunroof control lever.

Press and hold the CLOSE button once again within 5 seconds until the sunroof operates as follows:

•	Tilt → Slide Open → Slide Close Then release the lever.

6.	Reset procedure of panorama system is finished.

Protecting Motor From Overheating

In order to protect the sunroof motor from overheating from continuous motor operation, the sunroof ECU controls the Run-time and Cool-time of the motor as follows:

1.	The sunroof ECU detects the Run- time of motor

2.	Motor can be operated continuously for the 1st run-time (120 ± 10sec.).

3.	The continuous operation of motor stops after the 1st Run-time (120 ± 10sec.).

4.	Then Motor does not operate for the 1st Cool-time (18± 2sec.).

5.	Motor operates for the 2nd Run-time (10 ± 2 sec.) at the continued motor operation after 1st Cool-time (18 ± 2sec.).

6.	The continuous operation of motor stops operating after the 2nd Run-time (10 ± 2sec.)

7.	Motor does not operate for the 2nd Cool-time (18 ±2sec.).

Motor repeats the 2nd run-time and 2nd cool-time at the continued motor operation.

–	In case that motor is not operated continuously, the run-time is increased.

–	The Run-Time of motor is initialized to "0" if the battery or fuse is reconnected after being disconnected, discharged or blown.

T1 : 120 ± 10 sec., T2 : 18 ± 2 sec.,

T3 : 10 ± 2 sec., T4 : 18 ± 2 sec.

Sunroof Switch Repair procedures

Inspection [Front Sunroof Switch] 1. Disconnect the negative (-) battery terminal. 2. Remove the overhead console lamp assembly (A) after loosening 2 screws. 3. Check for continuity betwe ...

Surround View Monitoring (SVM) System

...

Other Information:

Owner
✽ NOTICE Maintenance Service and Record Retention are the owner's responsibility. You should retain documents that show proper maintenance has been performed on your vehicle in accordan ...

Electric motor
Charging connectors Traction battery Accessory battery Heat pump On-board charger Electric motor Charging cable The charging connectors 1 enable 3 types of charging: Domestic charging in mo ...

Kia Sedona: Sunroof Motor Repair procedures

Sunroof Switch Repair procedures

Surround View Monitoring (SVM) System

Other Information:

Categories