Kia Sedona: Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Body Electrical System / Keyless Entry And Burglar Alarm / Repair procedures

Inspection

Special care is needed for the following points in case of working with the non-gloss timber trimming.

•	Wrap a protective tape around tools used in disassembling such as screwdriver or remover.

•	Use caution in keeping and handling during disassembling/assembling because it is easily contaminated with lubricant and oil.

•	Use caution for the crash pad garnish and door trim upper garnish made of timber (Real wood) because they can be scratched or picked.

Front Door Lock Actuator Inspection

1.	Remove the front door trim. (Refer to Body - "Front Door Trim")

2.	Remove the front door module. (Refer to Body - "Front Door Module")

Disconnect the connector from the actuator.

No.	Pin Information
No.	Left front door	Right front door
1	AJAR Switch	Motor 1
2	COM	Motor 2
3	Lock/UnLock	-
4	Key Lock	Key Unlock
5	Key Unlock	Key Lock
6	-	Lock/UnLock
7	Motor 1	COM
8	Motor 2	AJAR Switch

4.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

5.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Lock Actuator Inspection (Power Sliding Door Only)

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Disconnect the connector from the actuator.

3.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

4.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Unlock Latch Actuator Inspection

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Disconnect the connector from the actuator.

3.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

4.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Lock Latch Inspection

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Remove the rear door screen.

Disconnect the connector from the door latch.

No.	Description
1	Detent Switch
2	Primary Switch
3	GND

4.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

5.	Check for continuity between terminals in half latching condition according to the table.

Tailgate Lock Module Inspection

1.	Remove the tailgate trim. (Refer to Body - "Tailgate Trim")

Disconnect the connector from the tailgate latch.

[Latch]

No.	Description
1	Secondary Switch
2	GND
3	Release Motor (-)
4	Release Motor (+)
5	Lock Switch
6	Primary Switch

[SCA]

No.	Description
1	Position Switch
2	GND
3	Cinch Motor (-)
4	Cinch Motor (+)

Tailgate Open Switch Inspection

1.	Remove the tailgate trim. (Refer to Body - "Tailgate Trim")

2.	Disconnect the connector from the tailgate open switch.

3.	Check for continuity between the terminals and ground according to the table.

Door Switch Inspection

1.	Remove the luggage side trim. (Refer to Body - "Luggage Side Trim")

2.	Check for continuity between the terminals and ground according to the table.

Hood Switch Inspection

1.	Remove the hood latch assembly. (Refer to Body - "Hood Latch Assembly")

2.	Disconnect the connector (A) from the hood switch.

3.	Check for continuity between the terminals and ground according to the table.

Burglar Horn Inspection

1.	Disconnect the burglar horn connector (A).

2.	Remove the burglar horn (A) after loosening the mounting nut.

3.	Test the burglar horn by connecting the battery power to terminal 1 and ground to terminal 2.

4.	The burglar horn should sound. If the burglar horn fails to sound, replace it.

Description and Operation

Description Burglar Alarm State [B/A State] B/A StateDescriptionDISARM 1) In "DISARM" state, vehicle start inhibition is disabled. So, when door, hood, or tailgate is opened, there is no ala ...

Transmitter Repair procedures

Inspection 1. Check that the red light flickers when the door lock or unlock button is pressed on the transmitter. 2. Remove the battery (A) and check voltage if the red light doesn''t flicker ...

Other Information:

Power outlet
Front Rear The power outlet is designed to provide power for mobile telephones or other devices designed to operate with vehicle electrical systems. The devices should draw less than 10 am ...

Rolling code programming
To train a garage door opener (or other rolling code equipped devices) with the rolling code feature, follow these instructions after completing the ...

Kia Sedona: Repair procedures

Description and Operation

Transmitter Repair procedures

Other Information:

Categories