Kia Sedona: Power Sliding Door (PSD) Drive Unit Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Body Electrical System / Power Sliding Door System / Power Sliding Door (PSD) Drive Unit Repair procedures

Removal

•	Put on gloves to protect your hands.

•	When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.

•	Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.

•	Take care not to bend or scratch the trim and panels.

[LH]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the rear combination lamp. (Refer to Lighting System - "Rear Combination Lamp")

Loosen the mounting screws and then remove the center rail cover (A) by using a screwdriver or panel remover.

For any parts damaged while removing the center rail cover, replace with new parts.

4.	Pull the rear cable (A) in the direction of the arrow.

Remove the rear cable (A) after falling down the cable end (B) in the direction of the arrow.

•	Be sure to check if the cable end is bent before installing the rear cable.

•	After installation, be sure to pull on the cable to check that it is securely mounted. (Loose cable may result in dislocation or damage of door.)

6.	Remove the front cable (A) from the center roller hinge (B).

7.	Remove the luggage side trim [LH]. (Refer to Body - "Luggage Side Trim")

8.	Remove the sub woofer speaker. (Refer to AUDIO or AVN System - "Speaker")

Disconnect the connector (A) and then remove the power sliding door drive unit (B) after loosening the nuts.

Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

[RH]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the rear combination lamp. (Refer to Lighting System - "Rear Combination Lamp")

Loosen the mounting screws and then remove the center rail cover (A) by using a screwdriver or panel remover.

For any parts damaged while removing the center rail cover, replace with new parts.

4.	Pull the rear cable (A) in the direction of the arrow.

Remove the rear cable (A) after falling down the cable end (B) in the direction of the arrow.

•	Be sure to check if the cable end is bent before installing the rear cable.

•	After installation, be sure to pull on the cable to check that it is securely mounted. (Loose cable may result in dislocation or damage of door.)

6.	Remove the front cable (A) from the center roller hinge (B).

7.	Remove the tail gate pillar trim [RH]. (Refer to Body - "Rear Pillar Trim")

8.	Remove the luggage side trim [RH]. (Refer to Body - "Luggage Side Trim")

9.	Remove the rear heater duct (A) after loosening the bolts.

10.	Pull up the bottom of rear A/C duct (A).

11.

Remove the third row seat belt upper anchor (A) after loosening the bolt.

Tightening torque:

39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

12.	Loosen the mounting bolt (A).

13.	Remove the rear A/C duct (A) after loosening the bolt.

14.	Disconnect the rear heater main connector.

15.	Separate the rear Heater & A/C unit (A) after loosening the nut.

16.

Disconnect the connector (A) and then remove the power sliding door drive unit (B) after loosening the nuts.

Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

Installation

[LH]

Install the power sliding door drive unit after connecting the connector.

Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

2.	Install the sub woofer speaker.

3.	Install the luggage side trim [LH].

4.	Install the front, rear cable.

5.	Install the center rail cover.

6.	Install the rear combination lamp.

7.	Connect the negative (-) battery terminal.

[RH]

Install the power sliding door drive unit after connecting the connector.

Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

2.	Install the rear heater & A/C unit.

3.	Connect the rear heater main connector.

4.	Install the rear A/C duct.

Install the third row seat belt upper anchor.

Tightening torque:

39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

6.	Install the heater duct.

7.	Install the luggage side trim [RH].

8.	Install the tail gate pillar trim [RH].

9.	Install the front, rear cable.

10.	Install the center rail cover.

11.	Install the rear combination lamp.

12.

Connect the negative (-) battery terminal.

•	Be sure to connect the power after installing the door to the chassis.

•	After replacing the power sliding door drive unit, the "power sliding door reset" procedure must be performed.

•	Check for normal operation whenever a power sliding door component is removed or replaced. If a chime sound is heard, check the DTC, wiring harness and cable connections.

Troubleshooting

Failure Check-up Elements The following is to be checked before inspecting the Power Sliding Door system parts. 1. Manual operation Check if the sliding door operates manually. Shift to ''OFF'' ...

Power Sliding Door (PSD) Control Module Components and Components Location

Components Connector Pin Information No.Connector AConnector BConnector CConnector D1-Detent Switch (Left side)Clutch Return (Left side)Logic battery 2-Child Safety Lock Switch (Left side)Quad S ...

Other Information:

Power tailgate opening height user setting
The driver may set the height of a fully opened tailgate by following the below instruction. 1. Confirm the position of the power door ON/OFF button is ON (not depressed). 2. Position the tailga ...

Horn
To sound the horn, press the horn symbols on your steering wheel. Check the horn regularly to be sure it operates properly. ✽ NOTICE To sound the horn, press the area indicated by the hor ...

Kia Sedona: Power Sliding Door (PSD) Drive Unit Repair procedures

Troubleshooting

Power Sliding Door (PSD) Control Module Components and Components Location

Other Information:

Categories