Kia Optima Manuals

Kia Sedona: Rear Axle Repair procedures - Rear Axle Assembly - Driveshaft and axle - Kia Sedona YP Service ManualKia Sedona: Rear Axle Repair procedures

Third generation YP (2014-2025) / Kia Sedona YP Service Manual / Driveshaft and axle / Rear Axle Assembly / Rear Axle Repair procedures

Removal
1.
Remove the front wheel and tire (A) from front hub.
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
   
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

2.
Remove the rear caliper assembly.
(Refer to Brake System - "Rear Disc Brake")
3.
Remove the parking brake cable.
(Refer to Brake System - "Parking Brake Assembly")
4.
Remove the rear Shock absorber bolt (A) and nut (B).
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

5.
Loosen the nut and remove the rear shock absorber.

6.
Loosen the bolt and nut and then remove the rear assist arm (A) from the rear axle.

7.
Use the special tools (09568-4A000) to remove the assist arm from the knuckle.

8.
Support the lower arm (A) with jack.

9.
Remove the bolt (A) from the rear upper arm.
Tightening torque:
137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)

10.
Remove the bolt (B) from the lower arm.

11.
Remove the wheel speed bracket bolt (A).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 1.4 lb-ft)

12.
Loosen the bolt and remove the rear axle and trailing arm (A) on the vehicle body side member.
Tightening torque:
98.1 ~ 117.7 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.8 lb-ft)

13.
Install in the reverse order of removal.
   
Use the SST (09581-11000) when installing the brake caliper assembly.
(Refer to Brake System - "Rear Disc Brake")
14.
Check the rear alignment.
(Refer to Suspension System - "Rear Alignment")
Disassembly
1.
Remove the hub assembly mounting bolts (A-4ea) from the rear axle carrier (B).
Tightening torque:
78.5 ~ 88.3N.m (8.0 ~ 9.0kgf.m, 57.9 ~ 65.1lb-ft)

2.
Remove the hub assembly (C) and the parking brake assembly (B) from the rear axle carrier (A).

3.
Assemble in the reverse order of disassembly.
Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the rear axle carrier for cracks.
Rear Hub - Carrier Repair procedures
Removal 1. Remove the front wheel and tire (A) from front hub. Tightening torque: 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)     Be careful not to dama ...

Suspension System
...

Other Information:

Auto Defogging Sensor (DATC only) Description and Operation
Description The auto defogging sensor is installed on the front window glass. The sensor judges and sends signal to blow out wind for defogging if moisture occurs. On receiving the signal from ...

Steering Column and Shaft Repair procedures
Removal 1. Disconnect the battery negative cable from the battery and then wait for at least 30 seconds. 2. Turn the steering wheel so that the front wheels can face straight ahead. 3. Rem ...

Categories


Copyright В© www.kisedona.com 2016-2025