Kia Optima Manuals

Kia Sedona: SS-B Solenoid Valve(ON/OFF) Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sedona YP Service ManualKia Sedona: SS-B Solenoid Valve(ON/OFF) Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / SS-B Solenoid Valve(ON/OFF) Repair procedures

Inspection
1.
Turn ignition switch OFF.
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Disconnect the solenoid valve connector (A).

4.
Measure the resistance between power terminal (5) and signal terminal (12).
Specification : 10.0 ~ 11.0 Ω

Removal
1.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.
Tightening torque:
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
3.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
4.
Remove the wiring bracket (A) and the air breather hose (B).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

5.
Lift the vehicle after loosening valve body cover upper bolts.
6.
Remove the valve body cover (A) by loosening bolts.
Tightening torque:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

7.
Remove the solenoid valve harness (A) and oil temperature sensor (B) after removing the bolts.
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

8.
Remove solenoid valve support bracket (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

9.
Remove the SS-B solenoid valve (A).

Installation
1.
Install in the reverse order of removal.
   
•
The existing solenoid valve O-ring (A) must be replaced with new one. (Do not reuse it.)

•
The existing valve body cover gasket (A) must be replaced with new one. (Do not reuse it.)

•
Refill the automatic transaxle with fluid.
(Refer to Hydraulic System - "Fluid")
•
Confirm that there is no fluid leakage on connections after repairing.
SS-B Solenoid Valve(ON/OFF) Schematic Diagrams
Circuit Diagram ...

Inhibitor Switch Specifications
Specification ItemSpecificationPower supply (V)12Output typeCombination of output signals Signal Code Table 　PP-RRR-NNN-DDSignal "1"12V12V00000Signal "2"012V12V12V000Signal "3"00012V12V12 ...

Other Information:

Components and Components Location
Component Location 1. AVN head unit2. Tweeter speaker3. Center speaker4. Roof antenna5. Front speaker6. Rear speaker7. Sub woofer speaker8. Antenna feeder cable9. Antenna cable connector10. Exter ...

Automatic transaxle
Depress the brake pedal and the lock release button when shifting. (If the shift lock system is not equipped, it is not necessary to depress the brake pedal. However, it is recommended to depre ...

Categories

Copyright © www.kisedona.com 2016-2026