Kia Sedona: Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Engine Control / Fuel System / Fuel Delivery System / Repair procedures

Fuel Pressure Test (Low pressure system)

Release the residual pressure in fuel line.

(Refer to the Fuel Delivery System - Repair Procedures - "Release Residual Pressure in Fuel Line").

When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of “Release Residual Pressure in Fuel Line” work.

Install the Special Service Tool (SST).

(1)

Disconnect the low pressure fuel feed tube from the low pressure inlet of high pressure fuel pump.

There may be some residual pressure even after “Release Residual Pressure in Fuel Line” work, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.

(2)	Install the special service tool for measuring the fuel pressure between the low fuel feed tube and the low pressure inlet of high pressure fuel pump (Refer to the figure below).

3.	Inspect fuel leakage on connections among the low fuel feed tube, the low pressure inlet of high pressure fuel pump, and the SST components with IG ON.

Measure Fuel Pressure.

(1)

Start the engine and measure the fuel pressure at idle.

Fuel Pressure: 470.7 ~ 510 kPa (4.8 ~ 5.2 kgf/cm², 68.3 ~ 74 psi)

If the fuel pressure differs from the standard value, repair or replace the related part (Refer to the table below).

Fuel Pressure	Cause	Related Part
Too Low	Fuel filter clogged	Fuel Filter
Too Low	Fuel leakage	Fuel Pressure Regulator
Too High	Fuel pressure regulator stuck	Fuel Pressure Regulator

(2)

Stop the engine, and then check for the change in the fuel pressure gauge reading.

Standard Value: The gauge reading should hold for about 5 minutes after the engine stops

If the gauge reading should not be held, repair or replace the related part (Refer to the table below).

Fuel Pressure (After Engine Stops)	Cause	Related Part
Fuel Pressure Drops Slowly	Leakage on injector	Injector
Fuel Pressure Drops Immediately	Check valve of fuel pump stuck open	Fuel Pump

(3)	Turn the ignition switch OFF.

Release the residual pressure in fuel line.

(Refer to the Fuel Delivery System - Repair Procedures - "Release Residual Pressure in Fuel Line").

When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of “Release Residual Pressure in Fuel Line” work.

Test End

(1)	Remove the Special Service Tool (SST) from the low pressure fuel feed tube and the low pressure inlet of high pressure fuel pump.

(2)	Connect the low pressure fuel feed tube and the low pressure inlet of high pressure fuel pump.

Release Residual Pressure in Fuel Line

Whenever the high pressure fuel fuse, fuel pipe, delivery pipe, or injector is removed immediately after shutting off the engine, an injury may be caused by the release of highly pressurized fuel. Release the residual pressure in the high pressure fuel line by referring to the "Residual fuel pressure release procedure" below before removing any high pressure fuel system components.

Wear safety glasses and fuel resistant gloves.

1.	Turn the ignition off and disconnect the battery negative (-) terminal.

2.	Remove the fuel pump fuse (A).

3.	Reconnect the battery negative (-) terminal.

4.	Run the engine for about 1 minutes to lower the pressure in the low pressure line.

5.	Turn the engine off.

6.	Disconnect the low pressure fuel line quick connector at the High Pressure Pump. Use rags to cover opening and catch spills while removing the fuel line.

7.	Start the engine, let it idle and then turn the ignition switch OFF after the engine has stopped on its own.

8.	Proceed with the service or repair. Use rags to cover opening and catch spills when opening up the high pressure system.

9.	Reinstall / re-connect all components in reverse order of removal. Start engine and confirm proper operation, and make sure there are no fuel leaks.

10.	After completing, clear DTC(s) using GDS scan tool. (The procedure descripbed above will cause DTC to set.)

Components and Components Location

Components Location [Fuel Tank] 1. Fuel Tank2. Fuel Pump3. Fuel Filter4. Fuel Pressure Regulator5. Canister6. Fuel Tank Air Filter7. Fuel Tank Pressure Sensor (FTPS)8. Canister Close Val ...

Fuel Tank Repair procedures

Removal 1. Release the residual pressure in fuel line. (Refer to the Fuel Delivery System - Repair Procedures - "Release Residual Pressure in Fuel Line") 2. Turn the ignition switch OFF and ...

Other Information:

Components and Components Location
Component Location 1. Auto light sensor2. Head lamps3. Lighting switch (Auto)4. Tail lamps5. BCM (Body Control Module) ...

Rear window wiper blade
1. Raise the wiper arm and pull out the wiper blade assembly. 2. Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place. 3. Make ...

Kia Sedona: Repair procedures

Components and Components Location

Fuel Tank Repair procedures

Other Information:

Categories