Kia Optima Manuals

Kia Sedona: Windshield Wiper-Washer Switch Repair procedures - Windshield Wiper/Washer - Body Electrical System - Kia Sedona YP Service ManualKia Sedona: Windshield Wiper-Washer Switch Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Body Electrical System / Windshield Wiper/Washer / Windshield Wiper-Washer Switch Repair procedures

Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
3.
Remove the steering column shroud lower / upper panel.
(Refer to Body - "Steering Column Shroud Panel")
4.
Remove the clock spring.
(Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")
5.
Disconnect the multifunction switch aseembly connector (A).

6.
Remove the multifunction switch assembly (A) after loosening 2 screws.

Installation
1.
Install the multifunction switch after connecting the connector.
2.
Install the clock spring and steering.
3.
Install the upper and lower shroud.
4.
Install the steering wheel.
5.
Connect the negative (-) battery terminal.
Inspection (With GDS)
1.
When each switch is pressed, check the resistance between multi-function switch terminals. If the resistance does not match the specification, replace the switch.
Description
Switch
Terminal No.
Resistance value (Ω, ±1%)
Wiper switch signal
MIST
1 - 9
330
OFF
∞
INT (AUTO)
800
Low
1800
High
5700
Front wiper INT volume
Volume 1
7 - 9
330
Volume 2
690
Volume 3
1310
Volume 4
2610
Volume 5
7310
Fog lamp switch
OFF
 9 - 10
∞
ON
910
Turn signal lamp switch
OFF
9 - 12
∞
Left
910
Right
2910
Head lamp Passing / High beam switch
OFF
9 - 13
∞
Passing
910
Dimmer
2910
Light Switch
OFF
9 - 14
∞
Auto
680
Tail lamp
1680
Head lamp (Low)
5580

2.
The body electrical system can be quickly diagnosed with the GDS.
The diagnostic system (GDS) provides the following information.
(1)
Self diagnosis : Checking the failure code (DTC) and display
(2)
Current data : Checking the system input/output data state
(3)
Actuation test : Checking the system operation condition
(4)
Additional function : Other controlling such as he system option and zero point adjustment
3.
Select the ''Car model'' and the system to be checked in order to check the vehicle with the tester.
4.
Select the ''Body Control Module (BCM)'' to check the Body Control Module (BCM).
5.
Select the ''Current data" menu to search the current state of the input/output data.
The input/output data for the sensors corresponding to the Body Control Module (BCM) can be checked.

Components and Components Location
Component Location 1. Windshield wiper arm & blade2. Wiper & washer switch3. Windshield washer hose & nolzzle4. Washer reservoir5. Washer motor6. Washer fluid level sensor7. Wiper mot ...

Front Wiper Motor Components and Components Location
Component Location 1. Cap2. Nut3. Wiper arm & blade4. Rivet5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly8. Wiper motor connector ...

Other Information:

Operating condition
This system will activate when the indicator on the rear parking assist OFF button is not illuminated. If you desire to deactivate the rear parking assist system, press the rear parking assis ...

Input Speed Sensor Components and Components Location
Component Location 1. Output speed sensor 2. Input speed sensor ...

Categories


Copyright © www.kisedona.com 2016-2024