Kia Optima Manuals

Kia Sedona: Torque Converter Control Solenoid Valve (T/CON_VFS) Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sedona YP Service ManualKia Sedona: Torque Converter Control Solenoid Valve (T/CON_VFS) Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / Torque Converter Control Solenoid Valve (T/CON_VFS) Repair procedures

Inspection
1.
Turn ignition switch OFF.
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Disconnect the solenoid valve connector (A).

4.
Measure the resistance between power terminal (10) and signal terminal (2).
Specification : 5.1 ± 0.3 Ω

Removal
1.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.
Tightening torque:
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
3.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
4.
Remove the wiring bracket (A) and the air breather hose (B).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

5.
Lift the vehicle after loosening valve body cover upper bolts.
6.
Remove the valve body cover (A) by loosening bolts.
Tightening torque:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

7.
Remove the solenoid valve harness (A) and oil temperature sensor (B) after removing the bolts.
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

8.
Remove solenoid valve support bracket (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

9.
Remove the torque converter control solenoid valve (B) after loosening the bolt (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Installation
1.
Install in the reverse order of removal.
   
•
The existing valve body cover gasket (A) must be replaced with new one. (Do not reuse it.)

•
Perform the procedures below after replacing the solenoid valve.
1)
Refill the automatic transaxle with fluid.
(Refer to Hydraulic System - "Fluid")
2)
Reset the automatic transaxle adaptive values using the GDS.

3)
Perform the TCM adaptive values learning procedure.
(Refer to Automatic Transaxle Control System - "Repair procedures")
4)
Confirm that there is no fluid leakage on connections after repairing.
Torque Converter Control Solenoid Valve (T/CON_VFS) Schematic Diagrams
Circuit Diagram ...

35R Clutch Control Solenoid Valve(35R/C_VFS) Specifications
Specification Item SpecificationControl typeN/H (Normal High)Control pressure kpa (kgf/cm², psi)"500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42)"Current value (mA)50 ~ 850Coil resistance(Ω)5.1 ± 0.3 ...

Other Information:

Active ECO operation
Active ECO helps improve fuel efficiency by controlling the engine and transaxle. But fuel-efficiency can be affected by the driver's driving habits and road conditions. When the Active EC ...

Seat Belt Buckle Switch (BS) Repair procedures
Removal 1. Disconnect the battery negative cable and wait for at least 30 seconds before beginning to work. 2. Remove the front seat assembly. (Refer to Body - "Front seat") 3. Loosen th ...

Categories


Copyright © www.kisedona.com 2016-2024