Kia Sedona: Steering Column and Shaft Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Steering System / Electric Power Steering / Steering Column and Shaft Repair procedures

Removal

1.	Disconnect the battery negative cable from the battery and then wait for at least 30 seconds.

2.	Turn the steering wheel so that the front wheels can face straight ahead.

3.	Remove the airbag module. (Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")

Disconnect the connector & lock nut (A) and then remove the steering wheel by using special service tools (09561-11001).

Tightening torque :

39.2 ~ 49.0 N.m (4.0 ~ 4.5 kgf.m, 28.9 ~ 36.2 lb-ft)

•	When removing the steering wheel, do not impact it by hammering as it may damage the steering column.

5.	Remove the steering column shroud. (Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")

6.	Remove the clock spring. (Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")

7.	Remove the multifunction switch. (Refer to Body Electrical System - "Multifunction switch")

8.	Remove the crash pad lower panel. (Refer to Body (Interior and Exterior) - "Crash Pad Lower Panel")

Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.

Tightening torque :

32.4 ~ 37.3 N.m(3.3 ~ 3.8 kgf.m, 23.9 ~ 27.5 lb-ft)

•	Insert the universal joint to the gear box certainly.

•	Do not reuse the bolt.

10.	Loosen 4 bolts (A) and then remove the nick bolster panel (B).

11.	Remove 2 nuts (A) from the steering column shaft assembly.

12.	Remove the brake switch. (Refer to Brake System - "Brake Switch")

13.	Remove the bolt (A) from the steering column shaft assembly.

14.	Remove the steering column assembly.

15.	Install in the reverse order of removal.

16.

Perform the steering angle sensor calibration.

–	HPS : (Refer to Brake System - "Steering Angle Sensor")

–	EPS (MDPS) : (Refer to Electric Power Steering - " Repair procedures - ASP Calibration")

Disassembly

Universal joint assembly

Loosen the bolt (A) and then disconnect the universal joint assembly from the steering column assembly.

Tightening torque :

49.0 ~ 58.8 N.m(5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4 lb-ft)

2.	Reassemble in the reverse order of disassembly.

Inspection

1.	Check the steering column for damage and deformation.

2.	Check the joint bearing for damage and wear.

3.	Check the tilt bracket for damage and cracks.

4.	Check the key lock assembly for proper operation and replace it if necessary.

Schematic Diagrams

Circuit Diagram 1. Connector terminal TypePin NoDescriptionBattery1Battery -2Battery +Vehicle1-2-3-4-5-6-7IGN8High_CAN9Low_CAN10-11-12- 2. Circuit Diagram ...

Steering Gear box Repair procedures

Removal 1. Remove the front wheel and tire (A) from front hub. Tightening torque : 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft) • Be careful ...

Other Information:

Hood Latch Repair procedures
Replacement 1. Loosen the fastener and remove the front bumper upper cover (A). 2. Remove the hood lower latch assembly (A) mounting bolts. Tightening torque : 7.8 ~ 11.8N.m (0.8 ~ 1.2kgf. ...

Ignition Coil Schematic Diagrams
Circuit Diagram ...

Kia Sedona: Steering Column and Shaft Repair procedures

Schematic Diagrams

Steering Gear box Repair procedures

Other Information:

Categories