Kia Sedona: High Pressure Fuel Pump Repair procedures - Fuel Delivery System - Engine Control / Fuel System - Kia Sedona YP Service ManualKia Sedona: High Pressure Fuel Pump Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Engine Control / Fuel System / Fuel Delivery System / High Pressure Fuel Pump Repair procedures

Removal
   
When removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, injury may be caused by leakage of high pressure fuel. For this reason, do not attempt any repairing immediately after engine stops.
1.
Release the residual pressure in fuel line.
(Refer to the Fuel Delivery System - Repair Procedures - "Release Residual Pressure in Fuel Line")
2.
Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
3.
Remove the high pressure fuel fump foam (A).

4.
Disconnect the fuel pressure control valve connector (A) and fuel feed tube quick-connector (B).

5.
Remove the intake manifold.
(Refer to Engine Mechanical System - "Intake Manifold")
6.
Remove the high pressure fuel pipe.
(Refer to Fuel Delivery System - "Fuel Line")
7.
Remove the mounting bolts (A), and then remove the high pressure fuel pump (B) from the cylinder head assembly

High pressure fuel pump mounting bolt:
12.8 ~ 14.7 N.m (1.3 ~ 1.5 kgf.m, 9.4 ~ 10.9 lb-ft)

   
Unscrew in turns the two bolts in small steps (0.5 turns). When one of the two bolts is fully unscrewed while the other bolt still intact, the housing surface of the cylinder head may be broken due to tension of the pump spring.

Installation
   
•
Be sure that the low pressure fuel hose quick-connector (A) is completely connected to the high pressure fuel pump by the locking sound.
•
Double-check the complete connection of the low pressure fuel hose to the high pressure fuel pump by pulling it after connecting.
•
Be sure to install the high pressure fuel pipe (B) to the specified torques.
•
Because fuel leak may cause fire, thoroughly inspect leakage of all fuel line connection parts at engine start condition.

   
•
Before installing the high pressure fuel pump, position the roller tappet in the lowest position by rotating the crankshaft. Otherwise the installation bolts may be broken because of tension of the pump spring.
•
Do not reuse the used bolt.
•
Do not reuse the used high pressure fuel pipe.
•
When tightening the installation bolts of the high pressure fuel pump, tighten in turns the bolts in small steps (0.5 turns) after tightening them to hand-screwed torque.
•
Install the component with the specified torques.
•
First hand-tighten the fasteners fully until they are not fastened any more in order to have them inserted in place and then completely tighten to the specified torque using a torque wrench.
Bolts or nuts not tightened in a straight line with the matching bolt holes or fittings may cause fuel leakage due to broken threads.
•
Note that internal damage may occur when the component is dropped. In this case, use it after inspecting.
   
•
Apply engine oil to the O-ring (A) of the high pressure fuel pump, the roller tappet (B), and the protrusion (C). Also apply engine oil to the groove on the location where the protrusion (C) is installed.

1.
Install in the reverse order of removal.
   
Use the special service tool [SST No.: 09314-3V100] to install the high pressure fuel pipe.
Fuel Line Repair procedures
Inspection Visually check the fuel lines for cracks, leakage, loose connections, deformation or tank band looseness.Removal High pressure fuel pipe (High pressure fuel pipe ↔ Delivery pipe) ...

Automatic Transaxle System
...

Other Information:

Use approved window washer anti-freeze in system
To keep the water in the window washer system from freezing, add an approved window washer anti-freeze solution in accordance with instructions on the container. Window washer anti-freeze is avail ...

Armrest (2nd row seat)
Type A Type B (for SXL package) The 2nd row seats have the armrest located on the side of seatback. Type A To use the armrest, swing down the armrest to the lowest position. Type B To use th ...

Categories


Copyright © www.kisedona.com 2016-2024