Kia Sedona: Head Lamps Repair procedures - Lighting System - Body Electrical System - Kia Sedona YP Service ManualKia Sedona: Head Lamps Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Body Electrical System / Lighting System / Head Lamps Repair procedures

Removal
   
Head lamps become very hot during use; do not touch them or attach any hardware immediately after turning them off.
   
•
The head lamp bulb should not be removed from the head lamp assembly until just before installing a new bulb.
•
Leaving the head lamp bulb removed for an extended period of time may degrade the head lamp bulb performance.
•
Contaminants may enter the head lamp assembly where they can settle on the lens and reflector.
•
Never turn on the head lamps with the bulb removed from the head lamp assembly.
Head Lamp
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front bumper cover.
(Refer to Body - "Front Bumper Cover")
3.
Disconnect the head lamp connector (A) and mounting clip (B).

4.
Remove the head lamp (A) after loosening the bolts.

   
Be careful not to damage the retaining clips (A).

Installation
1.
Install the head lamp assembly.
2.
Connect the head lamp connector.
3.
Connect the negative (-) battery terminal.
Replacement
   
Turn the head lamp switch off to avoid high voltage.
   
•
HID lamp shall not be used on other cars. (This may cause fire.)
•
Fire may occur when HID lamp initially lights due to the fact that arc-discharge generates high voltage (max. 20,000V) and high current (12-13A), and are different from the halogen lamp specification.
•
Install the dust cover after confirming the locking state between bulb and bulb holder.
•
When testing the HID head lamp, turn the power on or off with switch between power supply and lamp because of high voltage.
•
Do not operate the head lamp switch with the bulb not installed, because it generates spark momently.
Bulb (HID)
1.
Remove the head lamp.
2.
Remove the dust caps (A) from the head lamp assembly after turning in the counterclockwise direction.

3.
Remove the bracket (A) after loosening the screws.

4.
Remove the ignitor lamp (B) after disconnecting the connector (A).

5.
Install in the reverse order of removal.
   
Turn the head lamp switch off to avoid high voltage.
   
•
Be careful not to damage the bulb and use genuine bulbs only.
•
Do not apply excessive force and fit it correctly.
•
Confirm the bulb locking
Bulb (high/low)
1.
Remove the head lamp.
2.
Remove the dust caps (A) from the head lamp assembly after turning in the counterclockwise direction.
[LOW]

[HIGH]

3.
Disconnect the head lamp low beam bulb connector (A).

4.
Remove the head lamp low beam bulb (B) after removing the socket (A) from the head lamp assembly.

5.
Disconnect the head lamp high beam bulb connector (A).

6.
Remove the head lamp high beam bulb (B) after removing the socket (A) from the head lamp assembly.

7.
Install in the reverse order of removal.
Turn Signal Lamp
1.
Turn the head lamp switch off.
2.
Remove the bulb socket (A) and bulb (B) from the head lamp assembly.

3.
Install in the reverse order of removal.
Ballast
1.
Remove the head lamp.
2.
Remove the ballast (A) after loosening the screws.

3.
Disconnect the connectors (A) from the ballast.

4.
Install in the reverse order of removal.
   
Confirm the ballast installation
Inspection
1.
Check the battery voltage. (Low beam will be on when the battery voltage is above 9V.)
2.
Check the fuse and relay.
3.
Check the polarity of ballast. (If the polarity is changed, low beam does not light on.)
4.
Check that the bulb connector is connected securely.
5.
Visually check bulb (no filament) : damaged glass, damaged upper parts and lower parts of glass tube.
6.
After (1)~(5), replace the ballast and the ignitor. (ballast assembly).

Characteristic
1.
Durable for vibration as there is no filament.
2.
HID lamps have longer lifetime than halogen lamps.
3.
Does not operate if polarity is changed.
4.
Operating input voltage : 9-16V
Head Lamp Aiming Instructions
[Mechanical aiming]
The head lamps should be aimed with the proper beam-setting equipment, and in accordance with the equipment manufacturer''s instructions.
   
If there are any regulations pertinent to the aiming of head lamps in the area where the vehicle is to be used, adjust so as to meet those requirements.
Alternately turn the adjusting gear to adjust the head lamp aiming. If beam-setting equipment is not available, proceed as follows :
1.
Inflate the tires to the specified pressure and remove any loads from the vehicle except the driver, spare tire, and tools.
2.
The vehicle should be placed on a level ground.
3.
Draw vertical lines (Vertical lines passing through respective head lamp centers) and a horizontal line (Horizontal line passing through center of head lamps) on the screen.
4.
With the head lamp and battery in normal condition, aim the head lamps so the brightest portion falls on the vertical lines.
A : Vertical
[Non Leveling Device]

[Leveling Device]

Head Lamp And Fog Lamp Aiming Point

1.
Head Lamp (Low beam)
–
Turn the low beam on without driver aboard.
–
The cut-off line should be projected in the cut-off line shown in the picture.
–
If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

Head lamp fogging
Check the below instruction procedure when the head lamp is fogged.

Head Lamps Description and Operation
HID Head Lamp 1. Bulb (1) Elements Xenon gas: Xenon gas activates the initial reaction for rapid illuminating. Molybdenum electrode: anode arcing Metal halide salts: color composing component ...

Turn Signal Lamp Repair procedures
Removal Door Mirror Turn Signal Lamp 1. Disconnect the negative (-) battery terminal. 2. Remove the mirror (A) from the mirror holder.     Be careful not to damage t ...

Other Information:

Smart key unit Components and Components Location
Components (1) Connector Pin Information No.Connector AConnector BConnector C1Immobilizer antenna GND outputB+IGN12Bumper antenna GND output--3Rear antenna GND output--4Interior antenna 2 GND ou ...

How does the air bag system operate
Air bags are activated (able to inflate if necessary) only when the ignition switch is turned to the ON or START position. The appropriate air bags inflate instantly in the event of a serious ...

Categories


Copyright © www.kisedona.com 2016-2024