Inspection |
1. |
With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
|
2. |
Connect positive (+) battery cables to terminal 2 and negative (-) battery cables to terminal 1. |
3. |
Check that the motor operates normally, the washer motor runs and water sprays from the front nozzles. |
4. |
If there is an abnormality, replace the washer motor.
[Front washer]
|
1. |
Disconnect the negative (-) battery terminal. |
2. |
Drain the washer fluid to less than 600 cc. |
3. |
Check for continuity between terminals No. 1 and No. 2 in each float position.
There should be continuity when the float is down.
There should be no continuity when the float is up. |
4. |
If the continuity is not as specified, replace the washer fluid level switch. |
5. |
If the continuity is not as specified, replace the washer fluid level switch (A). |
Removal |
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Disconnect the washer hose (A) and washer motor connector (B). |
6. |
Remove the front washer motor (A). |
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Disconnect the washer fluid level sensor switch connector (A). |
6. |
Remove the washer fluid level sensor switch (A). |
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH].
(Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Disconnect the washer hose (B) after disconnecting the reservoir tank mounting clip (A). |
6. |
Disconnect the washer hose (A), washer fluid level sensor switch connector (B), and washer motor connector (C). |
7. |
Disconnect the mounting clip (D). |
8. |
Remove the reservoir (A) after loosening the mounting bolts. |
Installation |
1. |
If Necessary, clean the washer motor filter.
|
2. |
Install the front washer motor. |
3. |
Install the front washer motor connector. |
4. |
Install the front wheel guard [RH]. |
5. |
Install the engine room under cover. |
6. |
Connect the negative (-) battery terminal. |
1. |
Install the washer fluid level sensor switch. |
2. |
Install the washer fluid level sensor connector. |
3. |
Install the front wheel guard [RH]. |
4. |
Install the engine room under cover. |
5. |
Connect the negative (-) battery terminal. |
1. |
If necessary, clean the washer motor filter.
|
2. |
Install the reservoir tank. |
3. |
Install the washer motor hose and connectors. |
4. |
Install the front wheel guard [RH]. |
5. |
Install the engine room under cover. |
6. |
Connect the negative (-) battery terminal. |
Fuel Filler Door Release Actuator Repair procedures
Removal
Fuel Filler Door Release Actuator
1.
Disconnect the negative (-) battery terminal.
2.
Remove the luggage side trim [LH].
(Refer to Body - "Luggage Side Trim")
3.
Disconnect the c ...
Exhaust Manifold Components and Components Location
Components
1. LH Exhaust manifold gasket2. LH Exhaust manifold3. LH Heat protector4. LH Exhaust manifold stay5. RH Exhaust manifold gasket6. RH Exhaust manifold7. RH Heat protector8. RH Exhaust m ...