Kia Sedona: Fluid Repair procedures - Hydraulic System - Automatic Transaxle System - Kia Sedona YP Service ManualKia Sedona: Fluid Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Automatic Transaxle System / Hydraulic System / Fluid Repair procedures

Inspection
Automatic Transaxle Fluid (ATF) Level Check
   
When checking the ATF level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
1.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
2.
Add 0.7 liter of ATF ATF SP-IV after removing the eyebolt (A).

3.
Start the engine to heat up the ATF.
   
Do not step on the brake and accelerator simultaneously to heat up the ATF.
4.
Check that the temperature of the ATF is between 50°C and 60°C (122-140°F) using the GDS.
5.
Move the shift lever slowly from "P" to "D", then back to "P". Repeat this sequence a total of two times and then move the shift lever to "N" range.
   
Pause in each range for more than 2 seconds.
6.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
7.
Lift the vehicle and remove the ATF level plug (A) from the valve body cover.
   
When removing the ATF level plug, keep the vehicle horizontal.

8.
Check the ATF level.

Normal: ATF flows out in a thin oil stream.
Excessive (abnormal): ATF flows out over 0.9 liter for 2 minutes.
Insufficient (abnormal): There is no fluid flow.

   
If the ATF level is too high or low, follow the instructions below.
•
Excessive: Drain until the ATF flows out in a thin oil stream.
•
Insufficient: Add until the ATF flows out in a thin oil stream.
9.
Install the ATF level plug (A).
   
The existing ATF level plug O-ring (A) must be replaced with new one. (Do not reuse it.)

10.
Lower the vehicle and install the eyebolt (A).

Tightening torque: 4.9 ~ 5.9 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

   
The existing eyebolt O-ring (B) must be replaced with new one. (Do not reuse it.)

Replacement
1.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.

Tightening torque:
33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

   
The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
3.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
4.
Remove the eyebolt (A).

5.
Fill the automatic transaxle with about 5.0 liters of ATF SP-IV through the ATF filler hole.
6.
Perform the ATF level check procedure.
(Refer to Fluid - "Inspection")
Fluid Components and Components Location
Components Location 1. ATF filler hole (eyebolt)2. ATF level plug3. ATF drain plug ...

Valve Body Components and Components Location
Components Location 1. Automatic transaxle2. Valve body assembly Components 1. Pressure control valve (PCV) adjust screw2. Solenoid valve bracket3. Oil temperature sensor4. Line pressure co ...

Other Information:

Inside Rear View Mirror Repair procedures
Replacement     • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. ...

Special Service Tools
Special Service Tools Tool Name / NumberIllustrationDescription09964-C1100SCC reflectorReflector to align the SCC radar09964-C1200Vertical / horizontal laserLaser to detect the center of the vehi ...

Categories


Copyright © www.kisedona.com 2016-2024