Never remove the radiator cap when the engine is hot. Serious
scalding could be caused by hot fluid under high pressure escaping from
the radiator.
When pouring engine coolant, be sure to shut the relay box
lid and not to let coolant spill on the electrical parts or the paint.
If any coolant spills, rinse it off immediately.
1.
Make sure the engine and radiator are cool to the touch.
2.
Remove the radiator cap (A).
3.
Remove the engine room under cover.
(Refer to Engine And Transaxle - "Engine Room Under Cover")
4.
Loosen the drain plug (A), and drain the coolant.
5.
Tighten the radiator drain plug securely.
6.
Remove, drain and reinstall the reservoir. Fill the tank
halfway to the MAX mark with water, then up to the MAX mark with
antifreeze.
7.
Fill the radiator with water through the radiator cap and tighten the cap.
To most effectively bleed air, pour water slowly while pressing on the upper / lower radiator hoses..
8.
Start the engine and allow it to warm up to normal operating
temperature. Wait until the cooling fans turn on 2-3 times. Accelerate
the engine to aid in purging trapped air. Shut the engine off.
9.
Wait until the engine is cool.
10.
Repeat steps 1 to 8 until the drained water runs clear.
11.
Fill fluid mixture with coolant and water (45~60%) (except
for North America, Europe and China : 45~50%) slowly through the
radiator cap.
Press the upper/lower hoses of the radiator so as to bleed air easily.
•
Use only genuine antifreeze/coolant.
•
For best corrosion protection, the coolant concentration must be maintained year-round at 45 ~ 60% minimum.
Coolant concentrations less than 45 ~ 60% may not provide sufficient protection against corrosion or freezing.
•
Coolant concentrations greater than 60% will impair cooling efficiency and are not recommended.
•
Do not mix different brands of antifreeze/coolants.
•
Do not use additional rust inhibitors or antirust products; they may not be compatible with the coolant.
12.
Start the engine and run until coolant circulates.
13.
When the cooling fan operates and coolant circulates, refill coolant through the radiator cap.
14.
Repeat step 11 until the cooling fan operates 3-5 times to sufficiently bleed air out of the cooling system.
15.
Install the radiator cap and fill the reservoir tank to the "MAX" (or "F") line (A) with coolant.
16.
Run the vehicle under idle until the cooling fan operates 2-3 times.
17.
Stop the engine and wait for the coolant to cool down.
18.
Repeat steps 10 to 15 until the coolant level doesn''t fall anymore to bleed air out of the cooling system.
As it is to bleed air out of the cooling system and refill
coolant when coolant has completely cooled down, recheck the coolant
level in the reservoir tank 2-3 days after replacing coolant.
Coolant capacity :
Approx. 11.5 L (3.04 U.S.gal., 12.15 U.S.qt., 10.11 lmp.qt.)
Inspection
Radiator hoses
1.
Check radiator hoses for the following:
(1)
Improper attachment
(2)
Leaks
(3)
Cracks
(4)
Damage
(5)
Loose connections
(6)
Chafing
(7)
Deterioration
Coolant level
1.
Check the coolant level in the coolant reservoir. Make sure it is between the "F" mark and "L" mark.
2.
If the coolant level in the coolant reservoir is at or below
the "L" mark, add coolant to bring it between the "L" and "F" marks,
then inspect the cooling system for leaks.
Coolant quality
1.
Remove the radiator cap.
2.
Check if there are any excessive deposits of rust or scale
around the radiator cap sub-assembly and radiator filler hole. Also, the
coolant should be free of oil.
If excessively dirty, clean the coolant passage and replace the coolant.
Engine Overheat Troubleshooting
Inspection RemedyVisual inspectionInspect for shortage of coolant in reservoir tank .Reinspect after replenishing coolant.Inspect for coolant pollution after remo ...
Disarmed stage
The system will be disarmed when
The doors (and tailgate) are unlocked with the transmitter (or smart key)
or the ignition key.
Pull the power sliding door out handle while the power door ON/ ...
Kia Sedona: Coolant Repair procedures
Troubleshooting
Cooling Fan Components and Components Location