Kia Optima Manuals

Kia Sedona: CVVT Oil Control Valve (OCV) Repair procedures - Engine Control System - Engine Control / Fuel System - Kia Sedona YP Service ManualKia Sedona: CVVT Oil Control Valve (OCV) Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Engine Control / Fuel System / Engine Control System / CVVT Oil Control Valve (OCV) Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the OCV connector.
3.
Measure resistance between the OCV terminals 1 and 2.
4.
Check that the resistance is within the specification.
Specification: 9.4 ~ 10.4 [20°C(68°F)]
Removal
[Bank 1/ Intake]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
2.
Remove the intake manifold.
(Refer to Engine Mechanical System - “Intake Manifold”)
3.
Disconnect the CVVT oil control valve connector (A).
4.
Remove the installation bolt (B), and then remove the valve from the engine.

[Bank 1/ Exhaust)]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
2.
Disconnect the CVVT oil control valve connector (A).

3.
Remove the cylinder head cover.
(Refer to Engine Mechanical System - “Cylinder Head Cover”)
4.
Remove the mounting bolt (A), and then remove the valve from the engine.

[Bank 2/ Intake]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
2.
Remove the intake manifold.
(Refer to Engine Mechanical System - “Intake Manifold”)
3.
Disconnect the CVVT oil control valve connector (A).
4.
Remove the installation bolt (B), and then remove the valve from the engine.

[Bank 2/ Exhaust]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
2.
Disconnect the CVVT oil control valve connector (A).

3.
Remove the cylinder head cover.
(Refer to Engine Mechanical System - “Cylinder Head Cover”)
4.
Remove the mounting bolt (A), and then remove the valve from the engine.

Installation
   
•
Install the component to the specified torques.
•
Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing.
   
•
Apply the engine oil to the valve O-ring.
   
•
Accurately distinguish the color of the valve and harness connectors in bank 1 and 2 when installing, otherwise the engine will operate abnormally (Refer to the table below).
Items
Component Side
Harness Side
Bank 1 (RH)
Grey
Bank 2 (LH)
Black

1.
Install in the reverse order of removal.
CVVT oil control valve mounting bolt:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
CVVT Oil Control Valve (OCV) Schematic Diagrams
Circuit Diagram ...

Variable Intake Solenoid (VIS) Valve Specifications
Specification ItemSpecificationCoil Resistance (Ω)30.0 ~ 35.0 [20°C(68°F)] ...

Other Information:

Rear Washer Switch Repair procedures
Inspection 1. Check for continuity between the terminals while operating the wiper and washer switch. If it is not in normal condition, replace wiper and wiper switch. Rear Wiper Switch Rear ...

Walk-out seat (2nd row seat for SXL package)
To get out from the 3rd row seat, 1. Lift the armrest up , lower the headrests to the lowest position and slide the seat inside. (if necessary). 2. Pull the walk-in strap (1) on the 2nd row seat ...

Categories


Copyright © www.kisedona.com 2016-2024