Kia Optima Manuals

Kia Sedona: Inhibitor Switch Repair procedures - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sedona YP Service ManualKia Sedona: Inhibitor Switch Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / Inhibitor Switch Repair procedures

Inspection
Power Circuit Inspection
1.
Disconnect the Inhibitor switch connector.
2.
Ignition KEY "ON"" & Engine "OFF"..
3.
Measure voltage between supplied power and ground at inhibitor switch circuit.
Specification: Approx. 12V
Signal Circuit Inspection
1.
Connect the Inhibitor switch connector.
2.
Ignition KEY "ON" & Engine "OFF".
3.
Measure the voltages between each terminal and chassis ground in each range (P, R, N, D).
Signal Code Table
　
P
P-R
R
R-N
N
N-D
D
Signal "1"
12V
12V
0
0
0
0
0
Signal "2"
0
12V
12V
12V
0
0
0
Signal "3"
0
0
0
12V
12V
12V
0
Signal "4"
0
0
0
0
0
12V
12V

Removal
1.
Place the shift lever into the "N" position.
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Disconnect the inhibitor switch connector (A) and loosen the shift cable mounting nut (B).

4.
Remove the manual control lever (B) and the washer after removing a nut (A).

5.
Remove the inhibitor switch (A) after loosening the bolts.

Installation
1.
Check that the shift lever is placed in the "N" position
2.
Install the inhibitor switch (A).
   
Lightly tighten the inhibitor switch mounting bolts so that necessary adjustments can be made.

3.
Install the manual control lever (A).
   
Lightly tighten the manual control lever nut so that necessary adjustments can be made.

4.
Align the hole (B) in the manual control lever with the "N" position hole (A) of the inhibitor switch and then insert the SST inhibitor switch guide pin (09480-A3800).

5.
Tighten the nut (A) and bolts (B) to the specified torque.
Tightening torque
:A : 17.7 ~ 24.5 N.m (1.8 ~ 2.5 kgf.m, 13.0 ~ 18.1 lb-ft)
B : 9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

6.
Remove the SST (09480-A3800) from the adjusment hole.
7.
Connect the inhibitor switch connector (A).
8.
Install the shift cable by tightening nut (B).
Tightening torque:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

9.
Install the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
Inhibitor Switch Schematic Diagrams
Circuit Diagram ...

Shift Lever Components and Components Location
Components 1. Shift lever2. Shift lever bracket3. Main shaft4. Manual mode switch housing5. Shift lock solenoid6. Key interlock switch7. Main connector8. Shift cable assembly9. Shift cable retain ...

Other Information:

Automatic turn off function
The interior lights automatically turn off approximately 20 minutes after the ignition switch is turned off, if the lights are in the ON position. If your vehicle is equipped with the theft alarm s ...

Front Impact Sensor (FIS) Components and Components Location
Components ...

Categories

Copyright © www.kisedona.com 2016-2026