Kia Sedona: Power Door Lock Actuators Repair procedures

Third generation YP (2014-2026) / Kia Sedona YP Service Manual / Body Electrical System / Power Door Locks / Power Door Lock Actuators Repair procedures

Inspection

Special care is needed for the following points in case of working with the non-gloss timber trimming.

•	Wrap a protective tape around tools used in disassembling such as screwdriver or remover.

•	Use caution in keeping and handling during disassembling/assembling because it is easily contaminated with lubricant and oil.

•	Use caution for the crash pad garnish and door trim upper garnish made of timber (Real wood) because they can be scratched or picked.

Front Door Lock Actuator Inspection

1.	Remove the front door trim. (Refer to Body - "Front Door Trim")

2.	Remove the front door module. (Refer to Body - "Front Door Module")

Disconnect the connector from the actuator.

No.	Pin Information
No.	Left front door	Right front door
1	-	AJAR Switch
2	Motor 2	COM
3	Motor 1	Lock / Unlock
4	Key Unlock	Key Lock
5	Key Lock	Key Unlock
6	Lock / Unlock	Motor 1
7	COM	Motor 2
8	AJAR Switch	-

4.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

5.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Lock Actuator Inspection (Power Sliding Door Only)

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Disconnect the connector from the actuator.

3.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

4.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Unlock Latch Actuator Inspection

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Disconnect the connector from the actuator.

3.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

4.	Check for continuity between terminals in half latching condition according to the table.

Rear Door Lock Latch Inspection

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Remove the rear door screen.

Disconnect the connector from the door latch.

No.	Description
1	Detent Switch
2	Primary Switch
3	GND

4.	Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

5.	Check for continuity between terminals in half latching condition according to the table.

Tailgate Lock Module Inspection

1.	Remove the tailgate trim. (Refer to Body - "Tailgate Trim")

Disconnect the connector from the tailgate latch.

[Latch]

No.	Description
1	Secondary Switch
2	GND
3	Release Motor (-)
4	Release Motor (+)
5	Lock Switch
6	Primary Switch

[SCA]

No.	Description
1	Position Switch
2	GND
3	Cinch Motor (-)
4	Cinch Motor (+)

Tailgate Open Switch Inspection

1.	Remove the tailgate trim. (Refer to Body - "Tailgate Trim")

2.	Disconnect the connector from the tailgate open switch.

3.	Check for continuity between the terminals and ground according to the table.

Door Switch Inspection

1.	Remove the luggage side trim. (Refer to Body - "Luggage Side Trim")

2.	Check for continuity between the terminals and ground according to the table.

Hood Switch Inspection

1.	Remove the hood latch assembly. (Refer to Body - "Hood Latch Assembly")

2.	Disconnect the connector (A) from the hood switch.

3.	Check for continuity between the terminals and ground according to the table.

Components and Components Location

Component Location 1. DDM (Driver Door Module)2. BCM & RF receiver3. Door lock switch4. Tail gate lock actuator & switch5. Front door lock actuator & switch6. Rear door lock actuator ...

Power Door Lock Switch Repair procedures

Inspection Diagnosis With GDS 1. The body electrical system can be quickly diagnosed for faulty parts using vehicle diagnostic system (GDS). The diagnostic system (GDS) provides the following in ...

Other Information:

Low Fuel
This warning message illuminates if the fuel tank is nearly empty. - When the low fuel level warning light is illuminates. - When the trip computer displays "--- km (or mile)" as range. ...

Canister Close Valve (CCV) Specifications
Specification ItemSpecificationCoil Resistance (Ω)19.5 ~ 22.5 [20°C(68°F)]Rated Voltage (V)12Operation Voltage (V)9 ~ 16Operation Release Voltage (V)Below 6 ...

Kia Sedona: Power Door Lock Actuators Repair procedures

Components and Components Location

Power Door Lock Switch Repair procedures

Other Information:

Categories